Заполните пропуски в инструкции следующими фразами 1_______________ press END. The message In-Use wi...: ответ на тест 223209 - Английский язык

Заполните пропуски в инструкции следующими фразами
1_______________, press END. The message In-Use will appear in the display for approximately two seconds after you press END.
Press END 2_________________ occur:
-   No one answers
-   You hear an engaged or equipment engaged tone (busy signal)
-   3________________ that the phone number is unobtainable
The phone number you dialed 4_______________ so you can easily repeat the call. Refer to Cast Number Re-dial for more information.

Заполните пропуски в инструкции следующими фразами
 When your call is finished,1_________ . The message In-Use will appear in the display for approximately two seconds after you press END.
Press END 2_________________ occur:
- No one answers
- You hear an engaged or equipment engaged tone (busy signal)
- 3________________ that the phone number is unobtainable.
The phone number you dialed 4_______________ so you can easily repeat the call. Refer to Cast Number Re-dial for more information.

Заполните пропуски в инструкции следующими фразами
To store a phone number in standard memory, 1_________________:
1.  Press MENU.
2.  Press YES 2___________________.
3.  Press YES to enter the Store Mem function.
4.  A display similar to the one on the left appears. Use the keypad to enter the name you want stored with the number. When a block character appears to the right of the letter entered, you can enter the next letter.
5.  Once you have entered the text, press Down Arrow to move to the number entry position.
6.  Enter the phone number. 3________________ before accessing Menu mode, that number can be used as the number to be stored in memory. To delete an entered number, press the CLR key.
7.  4________________ to store the number. The name and number are now stored in the first available memory position.

Заполните пропуски в инструкции следующими фразами
You can enter 1__________________ (three to ten digits) any of which you can dial when service is available. Even when the phone is locked for security purposes, you 2_____________ numbers that have been stored in emergency number memory.
To enter a number into Emergency Number memory, 3_________________:
1.  Press MENU.
2.  Press Down Arrow to move to Gen. Setup.
3.  Press YES.
4.  Press Up Arrow to move to Emergency.
5.  Press YES. You will be prompted to enter your security code (for more information on security codes, see Locks Menu, Sec. Code).
6.  Press Down Arrow to move to the location where you want the Emergency number to be stored.
7.  Enter the number.
8.  4________________ to store the selection.

Заполните пропуски в инструкции следующими фразами
The Backlight or 1_____________ and keypad can be set to be automatically turned off or turned on all the time.
In On mode, the illumination 2_________________ after the last key was pressed; ten seconds in Standby mode or 20 seconds in Store, Recall, and Menu modes. 3________________ or when a call or message is received it returns to On.
To lock or unlock the keypad, complete the following steps:
1.  Press MENU.
2.  Press Down Arrow to move to Gen. Setup.
3.  Press YES.
4.  Press Down Arrow to move to Backlight.
5.  Press YES.
6.  Press 4_______________ between the Auto and Off selections.
7.  Press YES to store the highlighted selection.

Заполните пропуски в инструкции следующими фразами
The Call Type selection allows you to request a type of call to connect to the system. 1________________ a digital or an analog channel. Requests are granted only as conditions allow. 2________________, check to see that the digital indicator shows that your request was granted. The phone will reset to Dual Mode setting when you:
- Replace the battery.
- Turn the phone off 3_______________ PWR key.
The display will indicate 4________________ with a reverse text D or A displayed in the upper left hand corner.